360 Degree Rotary Encoder Brick Sensor Module

The M274 360 Degree Rotary Encoder Module Brick Sensor is a rotary input device (as in knob) that provides an indication of how much the knob has been rotated AND what direction it is rotating in. It’s a great device for stepper and servo motor control.  You could also use it to control devices like digital potentiometers.

M274 360 rotary Degree encoder, is an incremental electro-mechanical device that converts the angular position or motion of a shaft or axle to digital code. The output of incremental encoders provides information about the motion of the shaft, which is typically further processed in processor/controllers into information such as speed, distance, and position.

You can use the lm35dz sensor in temperature measurement applications. Thanks to its small size, you can make more precise measurements by placing it in the area you want to measure the temperature.

Features:

1. Calibrated directly in Degree Celsius (Centigrade)
2. Linear at 10.0 mV/°C scale factor
3. 0.5°C accuracy guarantee-able (at a25°C)
4. Suitable for remote applications
5. Low cost due to wafer-level trimming
6. Operates from 4 to 30 volts
7. Less than 60 mA current drain
8. Low self-heating, 0.08°C in still air
9. Non-linearity only 0.25°C typical
10. Low impedance output, 0.1Ωfor 1 mA load

Scope of application:

• power supplies
• battery management systems
• motor driver protection circuit

Package Included:

• 1 x LM35DZ Temperature Sensor

DS18B20 Temperature Sensor Module is a digital temperature sensor, and you can easily connect it to Arduino with only one 4.7-pound resistor, base 1 – Ground 2 – Output – Base 3 to the positive of the source, with resistance to base 2 Is connected. The connection of this sensor to the Arduino via the 1-wire protocol is established. Therefore, several sensors can be connected only through one common wire to Arduino. The output is digitally accurate to 12 bits. Therefore, the temperature can be measured with a precision of 0.0625 º C.

Features:

1. Digital signal output
2. 18B20 Temperature Sensor Chip
3. Resolution adjustment ranges from 9-12 bytes.
4. Send data via a pin
5. Temperature measurement ranges: -55°C to +125°C, be accurate to 0.5°C.

Package Includes:

1 x DS18B20 Temperature Sensor Module

The DHT11 Temperature And Humidity Sensor Module with LED is a small humidity and temperature sensor that you can connect to your Arduino and get readings for temperature and humidity in the environment.

Features:

• DHT11 sensor with PCB and LED indicator along with cable; 3 to 5V power and I/O, 4 pins with 0.1″ spacing
• The board has pre-built 4.7K or 10K resistor, which you will need to use as a pull-up from the data pin to VCC.
• 2.5mA max current use during conversion (while requesting data)
• Good for 20-80% humidity readings with 5% accuracy
• Good for 0-50°C temperature readings ±2°C accuracy.

Package Includes:

• 1 x DHT11 Temperature And Humidity Sensor Module.
• 3 x Female to Female Connecting cable.

MPU6050 is a frequently preferred sensor in aircraft, balance robots and many other areas.
It is a 6-axis IMU board with a 3-axis Gyro and a 3-axis angular accelerometer.

Features:

• Operating Voltage: 3.0 V – 5.0 V
• Gyro Measurement Range: ±250, ±500, ±1000, ±2000 ⁰/s
• Angular Accelerometer Measurement Range: ±2, ±4, ±8, ±16 g
• Communication Interface : I2C
• Dimensions: 20.3mm X 15.6mm

Documents:

• Sample Arduino Application
• Arduino Playground
• Example Raspberry Pi Application

Package Included:

• 1 x MPU6050 Acceleration and Gyro Sensor Board
• 1 x 1x8 Header(Male)
• 1 x 1x8 Header(Male-90⁰)