Arduino Nano Type-C USB

Arduino Nano is a small motherboard based on the ATmega328P. It has about the same features as the Arduino Duemilanove, only it lacks a DC power jack. Arduino IDE application is needed 
for programming . The Arduino Nano is powered by the Mini-B USB connection. The power supply automatically selects the high voltage source. The operating voltage is in the range of 5V - 12V. However, the recommended operating voltage should be more than 7V. 9V batteries will be sufficient for operation. 

In this clone version of Arduino Nano board, CH340 IC is used instead of Standard FTDI or 16U2 chips. 
Thus, the cost was reduced, but there was no change in performance.  

Features:

• Micro-Controller: ATmega328P
• Operating Voltage: 5V
• Input Voltage (recommended): 7-12V
• Digital I/O Pins: 14 (6 of them to provide PWM output)
• Analog Input Pins: 8
• Flash Memory : 32 KB
• Operating Frequency: 16 MHz
• Dimensions : 19x43mm

Package Included:

• 1 x Arduino Nano Clone CH340
• 1 x USB C Cable

Features:

Package Includes:

Do you want to know the work of RFID Reader/Writer RC522 SPI S50 CARD AND KEYCHAIN, then this Product is best for you . With this Product, you can detect radio waves produced by a reader to detect the presence of (then read the data stored on) an RFID tag

This is RFID Reader/Writer RC522 SPI S50 CARD AND KEYCHAIN which works on non-contact 13.56mhz communication, is designed by NXP as low power consumption, low cost, and compact size read and write chip, is the best choice in the development of smart meters and portable hand-held devices.

It uses an advanced modulation system, fully integrated at 13.56MHz with all kinds of positive non-contact communication protocols. Support 14443A compatible answer signal. DSP deals with ISO14443A frames and error correction.

This module can fit directly in handheld devices for mass production. The module uses the 3.3V power supply and can communicate directly with any CPU board by connecting through the SPI protocol, which ensures reliable work, good reading distance.

Features :

1. Highly integrated analog circuitry to demodulate and decode responses.
2. Supports ISO/IEC 14443 A/MIFARE.
3. Typical operating distance in reading/Write mode up to 50 mm.
4. Supports ISO/IEC 14443 A higher transfer speed communication up to 848 kBd.
5. SPI up to 10 Mbit/s.
6. FIFO buffer handles 64 bytes send and receive.
7. Flexible interrupt modes.
8. Power-down by software mode.
9. Programmable Timer.
10. 2.5 V to 3.3 V power supply.
11. CRC coprocessor.
12. Internal self-test.

Package Includes

1 x RFID-RC522 Reader/Write Module
1 x Standard blank RFID card
2 x A Straight & right-angle header strip
1 x Special-shaped keychain RFID tag

Arduino Nano is a small motherboard based on the ATmega328P. It has about the same features as the Arduino Duemilanove, only it lacks a DC power jack. Arduino IDE application is needed
for programming . The Arduino Nano is powered by the Mini-B USB connection. The power supply automatically selects the high voltage source. The operating voltage is in the range of 5V - 12V. However, the recommended operating voltage should be more than 7V. 9V batteries will be sufficient for operation.

In this clone version of Arduino Nano board, CH340 IC is used instead of Standard FTDI or 16U2 chips.
Thus, the cost was reduced, but there was no change in performance.

Features:

• Micro-Controller: ATmega328P
• Operating Voltage: 5V
• Input Voltage (recommended): 7-12V
• Digital I/O Pins: 14 (6 of them to provide PWM output)
• Analog Input Pins: 8
• Flash Memory : 32 KB
• Operating Frequency: 16 MHz
• Dimensions : 19x43mm

Package Included:

• 1 x Arduino Nano Clone CH340

The Leonardo R3 Board Micro-USB compatible with Arduino is a micro-controller board base on the ATmega32u4. It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs);  a 16 MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button.

It contains everything need to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.

The Leonardo R3 Board differs from all preceding boards in that the ATmega32u4 has built-in USB communication; eliminating the need for a secondary processor.

This allows the Leonardo to appear to a connected computer as a mouse and keyboard; in addition to a virtual (CDC) serial / COM port. It also has other implications for the behavior of the board.

Features :

1. It’s a 100% pro micro Arduino Compatible Board.
2. Chip: ATmega32u4
3. Board Mode: LEONARDO R3
4. Color: As shown in the pictures 

Package Includes :

1 x Leonardo R3 Board

There are two versions of the Pro Mini. One runs at 3.3V and 8 MHz, the other at 5V and 16 MHz. To buy 3.3V/8MHz Pro Mini click on the name below

Pinout Diagram:

Features :

1. ATmega328P running at 16MHz with external resonator (0.5% tolerance)
2. 0.8mm Thin PCB
3. USB connection off board
4. Supports auto-reset
5. 5V regulator
6. Max 150mA output
7. Overcurrent protected
8. Weighs less than 2 grams!
9. DC input 5V up to 12V
10. Onboard Power and Status LEDs
11. Analog Pins: 8
12. Digital I/Os: 14
13. 6 PWM port: D3, D5, D6, D9, D10, D11.
14. Use For Atmel Atmega328P-AU microcontroller.
15. Support serial download.
16. Support 9V battery.

Package Includes :