Arduino Nano board without USB cable

SKU: ARD002
  1. Manufacturer: Arduino Officials
  2. Operating Voltage (logic level): 5V
  3. 8 analog inputs ports: A0 ~ A7
  4. 14 Digital input / output ports: TX, RX, D2 ~ D13
  5. 1 pair of TTL level serial transceiver ports RX / TX
  6. Using Atmel Atmega328P-AU MCU
  7. There is a bootloader installed in it
  8. Standard 0.1” spacing DIP (breadboard friendly).
  9. Manual reset switch.
175,00 EGP
[ti_wishlists_addtowishlist]Compare
SKU: ARD002 Categories: ,

Description

Arduino Nano is a small motherboard based on the ATmega328P. It has about the same features as the Arduino Duemilanove, only it lacks a DC power jack. Arduino IDE application is needed
for programming . The Arduino Nano is powered by the Mini-B USB connection. The power supply automatically selects the high voltage source. The operating voltage is in the range of 5V – 12V. However, the recommended operating voltage should be more than 7V. 9V batteries will be sufficient for operation.

In this clone version of Arduino Nano board, CH340 IC is used instead of Standard FTDI or 16U2 chips.
Thus, the cost was reduced, but there was no change in performance.

Features:

  • Micro-Controller: ATmega328P
  • Operating Voltage: 5V
  • Input Voltage (recommended): 7-12V
  • Digital I/O Pins: 14 (6 of them to provide PWM output)
  • Analog Input Pins: 8
  • Flash Memory : 32 KB
  • Operating Frequency: 16 MHz
  • Dimensions : 19x43mm

Package Included:

Additional information

Weight 0,0000 g
Dimensions 45 × 18 × 5 mm
Model Type

Nano

Microcontroller

ATmega328

Operating Voltage (VDC)

5

Input Supply Port

USB Mini

Input Voltage(Recommended)

7-12 V

Power Consumption (Watt)

1

Analog I/O Pins

8

Digital I/O Pins

22 (6 of which are PWM)

PWM Output Pins

6

Architecture

AVR

Clock Speed

16 MHz

Flash Memory

32KB

EEPROM

1 KB

SRAM

2

Shipment Weight

0.019 kg

Shipment Dimensions

9 × 6 × 3 cm

Reviews

There are no reviews yet.

Be the first to review “Arduino Nano board without USB cable”

Your email address will not be published. Required fields are marked *

Quick Comparison

SettingsArduino Nano board without USB cable removeRaspberry Pi Pico (RP2040) removeLeonardo R3 Board Micro-USB compatible with Arduino removePro Mini ATMEGA328P 5V/16M Blue removeCable For Arduino UNO/MEGA (USB A to B)-50 cm removeUltrasonic holder remove
NameArduino Nano board without USB cable removeRaspberry Pi Pico (RP2040) removeLeonardo R3 Board Micro-USB compatible with Arduino removePro Mini ATMEGA328P 5V/16M Blue removeCable For Arduino UNO/MEGA (USB A to B)-50 cm removeUltrasonic holder remove
Image
SKUARD002RP2040lenardoaa0150c1I123
Rating
Price175,00 EGP300,00 EGP300,00 EGP150,00 EGP15,00 EGP15,00 EGP
Stock
Out of stock
Out of stock
AvailabilityOut of stockOut of stock
Add to cart

Add to cart

Read more

Add to cart

Read more

Add to cart

Add to cart

Description
  1. Manufacturer: Arduino Officials
  2. Operating Voltage (logic level): 5V
  3. 8 analog inputs ports: A0 ~ A7
  4. 14 Digital input / output ports: TX, RX, D2 ~ D13
  5. 1 pair of TTL level serial transceiver ports RX / TX
  6. Using Atmel Atmega328P-AU MCU
  7. There is a bootloader installed in it
  8. Standard 0.1” spacing DIP (breadboard friendly).
  9. Manual reset switch.
  1. RP2040 microcontroller chip designed by Raspberry Pi
  2. Dual-core Arm Cortex M0+ processor, the flexible clock running up to 133 MHz
  3. 264KB of SRAM, and 2MB of onboard Flash memory
  4. 26 × multi-function GPIO pins
  5. 2 × SPI, 2 × I2C, 2 × UART, 3 × 12-bit ADC, 16 × controllable PWM channels
  6. Onboard temperature sensor
  1. Microcontroller: ATmega32u4
  2. Operating Voltage: 5V
  3. Input Voltage (Recommended): 7-12V
  4. Input Voltage (limits): 6-20V
  5. Digital I/O Pins: 20
  6. PWM Channels: 7
  7. Analog Input Channels: 12
  1. Microcontroller: ATmega328P
  2. Circuit Operating Voltage: 5V
  3. Clock frequency: 16MHz.
  4. 6 PWM port: D3, D5, D6, D9, D10, D11.
  5. Use For Atmel Atmega328P-AU microcontroller.
  6. Support serial download.
  7. Support 9V battery.
  8. A pair of TTL level serial port transceiver : RX / TX.
Content

Arduino Nano is a small motherboard based on the ATmega328P. It has about the same features as the Arduino Duemilanove, only it lacks a DC power jack. Arduino IDE application is needed
for programming . The Arduino Nano is powered by the Mini-B USB connection. The power supply automatically selects the high voltage source. The operating voltage is in the range of 5V - 12V. However, the recommended operating voltage should be more than 7V. 9V batteries will be sufficient for operation.

In this clone version of Arduino Nano board, CH340 IC is used instead of Standard FTDI or 16U2 chips.
Thus, the cost was reduced, but there was no change in performance.

Features:

  • Micro-Controller: ATmega328P
  • Operating Voltage: 5V
  • Input Voltage (recommended): 7-12V
  • Digital I/O Pins: 14 (6 of them to provide PWM output)
  • Analog Input Pins: 8
  • Flash Memory : 32 KB
  • Operating Frequency: 16 MHz
  • Dimensions : 19x43mm

Package Included:

Almost one and half-year before Raspberry Pi Foundation had launched a revolutionary update on their Single Board Computer (SBC) Pi 3 and become the most popular Microcontroller board in the community which is known as a Raspberry Pi 4. On the same timeline, the Raspberry Pi Foundation came with a new astonishing SBC named Raspberry Pi Pico. The main highlighted thing about RPi Pico is the Lowest cost and Smallest size development board from Raspberry Pi Foundation ever.  On the technical side, it is equipped with an RP2040 Microcontroller chip developed by Raspberry Pi Foundation itself. RP2040 is their first dual-core ARM Cortex M0+ processor-based latest small-sized, budget-friendly microcontroller. RP2040 Microcontroller chip The RP2040 is supported with both C/C++ and micro-python, meaning that if you’re a beginner and want to learn any of these languages, the Raspberry Pico would be the best product option to start with.

Features:

  1. RP2040 microcontroller chip designed by Raspberry Pi
  2. Dual-core Arm Cortex M0+ processor, the flexible clock running up to 133 MHz
  3. 264KB of SRAM, and 2MB of onboard Flash memory
  4. The castellated module allows soldering directly to carrier boards
  5. USB 1.1 with device and host support
  6. Low-power sleep and dormant modes
  7. Drag-and-drop programming using mass storage over USB
  8. 26 × multi-function GPIO pins
  9. 2 × SPI, 2 × I2C, 2 × UART, 3 × 12-bit ADC, 16 × controllable PWM channels
  10. Accurate clock and timer on-chip
  11. Onboard temperature sensor
  12. Accelerated floating-point libraries on-chip
  13. 8 × Programmable I/O (PIO) state machines for custom peripheral support
For more technical details go through Datasheet in attachments

Package Includes:

1 x Raspberry Pi Pico

The Leonardo R3 Board Micro-USB compatible with Arduino is a micro-controller board base on the ATmega32u4. It has 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs);  a 16 MHz crystal oscillator, a micro USB connection, a power jack, an ICSP header, and a reset button.

It contains everything need to support the microcontroller; simply connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started.

The Leonardo R3 Board differs from all preceding boards in that the ATmega32u4 has built-in USB communication; eliminating the need for a secondary processor.

This allows the Leonardo to appear to a connected computer as a mouse and keyboard; in addition to a virtual (CDC) serial / COM port. It also has other implications for the behavior of the board.


Features :

  1. It’s a 100% pro micro Arduino Compatible Board.
  2. Chip: ATmega32u4
  3. Board Mode: LEONARDO R3
  4. Color: As shown in the pictures 

Package Includes :

1 x Leonardo R3 Board

This is Pro Mini 5V/16MHz is a 3.3V Arduino running the 8MHz bootloader. It’s a great board that will get you up and running quickly. The Arduino Pro series is meant for users that understand the limitations of system voltage (5V), lack of connectors, and USB off-board. The Pro Mini is a microcontroller board base on the ATmega328P.  It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, an on-board resonator, a reset button, and holes for mounting pin headers. A six pin header can be connected to an FTDI cable to provide USB power and communication to the board. The Pro Mini Arduino is intended for semi-permanent installation in objects or exhibitions. The pin layout is compatible with the Mini Arduino.
There are two versions of the Pro Mini. One runs at 3.3V and 8 MHz, the other at 5V and 16 MHz. To buy 3.3V/8MHz Pro Mini click on the name below

Pinout Diagram:

Features :

  1. ATmega328P running at 16MHz with external resonator (0.5% tolerance)
  2. 0.8mm Thin PCB
  3. USB connection off board
  4. Supports auto-reset
  5. 5V regulator
  6. Max 150mA output
  7. Overcurrent protected
  8. Weighs less than 2 grams!
  9. DC input 5V up to 12V
  10. Onboard Power and Status LEDs
  11. Analog Pins: 8
  12. Digital I/Os: 14
  13. 6 PWM port: D3, D5, D6, D9, D10, D11.
  14. Use For Atmel Atmega328P-AU microcontroller.
  15. Support serial download.
  16. Support 9V battery.

Package Includes :

1 x Pro Mini ATMEGA328P 5V/16M – Blue – Standard Version

This is a Cable For Arduino UNO/MEGA (USB A to B) 3.11 feet you can use it to connect “Arduino Uno”, “Arduino Mega 2560″ or any board with the USB female A port of your computer. The cable length is approximately 120cm. Cable color and shape may vary slightly from an image as our stock rotates.

This is a standard-issue USB 2.0 cable. the kind that’s usually used for printers, Arduino, etc. Compatible with most SFE designed USB boards as well as USB Arduino boards like the Uno.

It is very important to understand the cheap USB cables or faulty USB cables may harm your Printers and cause errors again and again while printing important data. For the error-free and long life of your printers, you must use high-quality USB A to B printer cables. We are selling a highly robust and high-quality USB 2.0 Printer cable at a reasonable price.

Connect your USB printer, scanner and more to your computer. Transmits data at high speeds with the error-free, high-performance transmission.


Features :

  1. Fully compatible with the PC.
  2. Molded strain relief and PVC over-molding to ensure a lifetime of error-free data transmissions.
  3. Aluminum under mold shield helps meet FCC requirements on KMI/RFI interference.
  4. Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference.

Package Includes :

1 x Cable For Arduino UNO/MEGA (USB A to B) 3.11 feet

Weight0.00000.00000.00000.00000.00000.0000
Dimensions45 × 18 × 5 mmN/A68 × 54 × 20 mmN/AN/AN/A
Additional information
Weight 0,0000 g
Dimensions 45 × 18 × 5 mm
Model Type

Nano

Microcontroller

ATmega328

Operating Voltage (VDC)

5

Input Supply Port

USB Mini

Input Voltage(Recommended)

7-12 V

Power Consumption (Watt)

1

Analog I/O Pins

8

Digital I/O Pins

22 (6 of which are PWM)

PWM Output Pins

6

Architecture

AVR

Clock Speed

16 MHz

Flash Memory

32KB

EEPROM

1 KB

SRAM

2

Shipment Weight

0.019 kg

Shipment Dimensions

9 × 6 × 3 cm

Weight 0,0000 g
Weight 0,0000 g
Dimensions 68 × 54 × 20 mm
Model Type

Arduino Leonardo

Microcontroller Chip

ATmega32u4

Operating Voltage (VDC)

5

Input Voltage(Recommended)

7V-12V

Input Voltage (limit)

6V-20V

Analog I/O Pins

12

Digital I/O Pins

20

PWM Digital I/O Pins

7

Clock Speed

16 MHz

Flash Memory

32 KB

SRAM

2.5

EEPROM

1 KB

Weight 0,0000 g
Microcontroller

ATmega328P

Input Voltage (V)

5 to 12

Clock Frequency (MHz)

16

Analog I/O Pins

8

Digital I/O Pins

14

Weight 0,0000 g
Weight 0,0000 g
Select the fields to be shown. Others will be hidden. Drag and drop to rearrange the order.
  • Image
  • SKU
  • Rating
  • Price
  • Stock
  • Availability
  • Add to cart
  • Description
  • Content
  • Weight
  • Dimensions
  • Additional information
  • Attributes
  • Custom attributes
  • Custom fields
Click outside to hide the comparison bar
Compare