Brushless Motor 1400KV

Description: A2212/10T 1400KV Brushless Outrunner Motor

1400KV A2212 2212 10T 1400KV Brushless Motor BLDC Motor 2-3S Outrunner Motor With 3.5mm Male Banana Bullet Plug Jack Fixed Wing For F450 S500 Frame RC Drone Airplane Aircraft Multi-Copter Quad-Copter Helicopter

These are the best low price drone motors available in the market. Then here is the best deal for you !!!! These are our market cracking Brushless Motors when it comes to bestselling drone motors. The uniqueness of this BLDC Motor lies in low cost and highly satisfying performance in fly. These brushless motors for drones are imported from China. Our quality control team then test some of the random motors from each batch before setting them on sell. The A2212 10T 13T 1400Kv Brushless Motors for Drone are best compatible or used with SimonK 30A ESC and 1045 Propeller Set. This 1400kv brushless motor is equipped with the solid metal case which makes it reliable and durable. This A2212 10T Motor comes with the pre-soldered good quality connector for a fast and direct connection between ESC and the motor.

Specifications:

• Model: A2212 / 10T
• RPM / V: 1400 kV
• Maximum efficiency: 80%
• Maximum current performance: 4-10 A
• Current: 12 A / 60 s
• Working voltage: 7-12V

Application:

• Multirotors
• RC Airplanes
• UAV

Features:

• The steel design is capable of withstanding competitional conditions.
• Lightweight design makes them suitable for a wide range of Quadcopter and Hexacopter Frames.
• Compact size.
• Offers great performance and value for money.
• Smooth throttle response for best RC experience.

12V DC Solenoid Water Air Valve Switch (Normally Closed) – 1/2″ controls the flow of fluid (liquid or air) and acts as a valve between high-pressure fluid! This liquid valve would make a great addition to your robotic gardening project. There are two ½” (Nominal NPT) outlets. Normally, the valve is closed. When a 12V DC supply is applied to the two terminals, the valve opens and water can push through.

The valve works with the solenoid coil which operates electronically with DC 12 volt supply. As it is a normally closed assembly, it opens the flow of fluids as soon as it is powered ON and stops/blocks the flow when the supply voltage removed.

Note:  While Connecting Valve in Flow pipeline, you need to mind the Input and Output direction of the valve. It will work only if you connect it in the right direction. (Hint: Inside the value, at one side you will find the filter this is the input side of the value)

Features:

1. Compact and convenient.
2. Easily installed and serviced
3. Precise and reliable.
4. The installation direction can be arbitrary Angle
5. Pressure-regulating valve (steady flow valve) function similar to the water flow switch
6. Not only can it provide a steady flow, but it also prevents the dry burning.
7. Suitable for fluids like water, oil, air.

Package Includes:

1 x 12V Solenoid Water Air Valve Switch (Normally Closed) – 1/2″

Material: ABS

1. The yellow color
2. Product quote for 2 axes and 8folhas from 2conjuntos quote.
3. Wind leaf overall diameter: Φ100mm
4. Wind leaf total height: 60mm
5. Shaft hole diameter: 1.95mmΦ (mounting shaft 2.0mm)
6. Wind page number: 4pcs
7. For the mass production plant, there is a little burr forward, but not the effect on use.
8. Size: see the picture below
9. No retail package
10. Quantity: 1pc

Note: Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!!

Package includes:

• 1pc xMini Wind Turbine Blade Vertical Ax Micro Generator Blades Set Small New

If you want to make a robot which has lots of moving parts or if you want to control too many LEDs with PWM outputs,  then the limited PWM outputs of your microcontroller would be a big problem for you. To overcome this problem, the only thing you should do is to get a 16-Channel 12-Bit PWM/Servo Driver.

You can control 16 free-running PWM outputs with 16-Channel 12-Bit PWM/Servo Driver using only 2 pins. You can even chain up 62 breakouts to control up to 992 PWM outputs.

It’s an I2C-controlled PWM driver with a built-in clock. That means you do not need to continuously send it to signal to tie up your microcontroller, it is completely free running!

It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs. This is good when you want to control white or blue LEDs with 3.4+ forward voltages. 6 address select pins so you can wire up to 62 of these on a single I2C bus, a total of 992 outputs.

Features :

1. Adjustable frequency PWM up to about 1.6 KHz
2. 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
3. Configurable push-pull or an open-drain output
4. The output enable pin to quickly disable all the outputs
5. Terminal block for power input
6. Reverse polarity protection on the terminal block input
7. Green power-good LED
8. 3 pin connectors in groups of 4 so you can plug in 16 servos at once
9. Chainable design
10. A spot to place a big capacitor on the V+ line
11. 220-ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial.
12. This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers.

Package Includes :

This N20-6V-40 Rpm Micro Metal Gear Motor has small volume, torsion big, all metal gear, durable, not easy to wear. Great replacement for the rusty or damaged DC geared speed reduce motor on the machine. Widely used on Boat, Car, Electric Bicycle, Fan, Home Appliance.

The N20 Micro Gear 6V 40 RPM DC Motor (High Torque) is lightweight, high torque, and low RPM motor. It is equipped with gearbox assembly so as to increase the torque of the motor. It has a cross-section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. It has a very small size so as fit in complex spaces of small-scale application. One can connect this Micro Gear Motor to wheels to drive them from one place to other while carrying high loads.

This N20 Micro Gear 40 RPM 6V DC Motor (High Torque) has small volume, torsion big, all metal gear, durable, not easy to wear. Great replacement for the rusty or damaged DC geared speed reduce motor on the machine. Widely used on Boat, Car, Electric Bicycle, Fan, Home Appliance.

Note: Image of product may differ from the Actual Product.

Features :

1. This is a DC Mini Metal Gear Motor, ideal for making robots
2. Lightweight, high torque and low RPM.
3. Fine craftsmanship, durable, not easy to wear.
4. With excellent stall characteristics, can climb hills easily.
5. You can also easily mount a wheel on the motor’s output shaft.

Package Includes :

1 x N20-6V-40 Rpm Micro Metal Gear Motor