DS18B20 Water Proof Temperature Probe – Black (1m)

The Flame Sensor Module can detect flames in the 760 – 1100 nanometer wavelength range. Small flames like a lighter flame can be detected at roughly 0.8m. The detection angle is roughly 60 degrees and the sensor is particularly sensitive to the flame spectrum.

An on-board LM393 op-amp is used as a comparator to adjust the sensitivity level. The sensor has a digital and analog output and sensitivity can be adjusted via the blue potentiometer.

This Flame Sensor Module is used to detect fire/flame source or other light sources of the wavelength in the range of 760nm – 1100 nm. It is based on the YG1006 sensor which is a high speed and high sensitive NPN silicon phototransistor. Due to its black epoxy, the sensor is sensitive to infrared radiation.

The sensor can be a great addition in a firefighting robot, it can be used as a robot eyes to find the fire source. When the sensor detects flame the Signal LED will light up and the D0 pin goes LOW.

The module has 2 outputs: Analogue, which gives a real-time voltage output signal on thermal resistance, and digital which allows temperature thresholds to be set via a potentiometer.

Features :

1. High Photo Sensitivity
2. Fast Response Time
3. Sensitivity adjustable
4. Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm.
5. Detection range: up to 100 cm.
6. Adjustable detection range.
7. Detection angle about 60 degrees, it is sensitive to the flame spectrum.
8. Comparator chip LM393 makes module readings stable.
9. Operating voltage 3.3V-5V.
10. Digital and Analog Output. 
11. Power indicator and digital switch output indicator.

Package Includes :

1 x Flame Sensor Module

The Water Level Depth Detection Sensor for Arduino has Operating voltage DC3-5V and Operating current less than 20mA. The Sensor is the Analog type which produces analog output signals according to the water pressure with its Detection Area of 40x16mm.

The Water Level Sensor is an easy-to-use and cost-effective with high level/drop recognition sensor by having a series of parallel wires exposed traces measure droplets/water volume in order to determine the water level.

Easy to complete water to analog signal conversion and output analog values can be directly read Arduino development board to achieve the level alarm effect.

Package Includes :

1 x Water Level Sensor Depth of Detection Water Sensor for Arduino

The DHT11 Temperature And Humidity Sensor Module with LED is a small humidity and temperature sensor that you can connect to your Arduino and get readings for temperature and humidity in the environment.

Features:

• DHT11 sensor with PCB and LED indicator along with cable; 3 to 5V power and I/O, 4 pins with 0.1″ spacing
• The board has pre-built 4.7K or 10K resistor, which you will need to use as a pull-up from the data pin to VCC.
• 2.5mA max current use during conversion (while requesting data)
• Good for 20-80% humidity readings with 5% accuracy
• Good for 0-50°C temperature readings ±2°C accuracy.

Package Includes:

• 1 x DHT11 Temperature And Humidity Sensor Module.
• 3 x Female to Female Connecting cable.

This is JoyStick Module PS2 Breakout Sensor very similar to the ‘analog’ joysticks on PS2 (PlayStation 2) controllers. Directional movements are simply two potentiometers – one for each axis. Pots are ~10k each. This joystick also has a select button that is actuated when the joystick is press down.

With the help of this Joystick Module, you can measure position coordinates on the X and Y axis by moving the “hat”. It also contains a switch that is press-able by pushing the “hat”.It also contains a switch that is press-able by pushing the “hat” down. Similar to the XBOX controller.

The X and Y axes are two 10k potentiometers which control 2D movement by generating analog signals. When the module is in working mode, it will output two analog values, representing two directions. This module uses the 5V power supply, and value, when reading through analog input, would be about 2.5V, a value will increase with joystick movement and will go up till maximum 5V; the value will decrease when the joystick is moved in other direction till 0V.

Applications:

1.As square wave signal generator which generates a square wave signal

2. To provide a signal to the stepping motor driver

3. Adjustable pulse generation for chip use

4. Produce variable pulse signal, the control-related circuit (PWM dimming, speed)

Module Description:

Frequency is divided into three ranges:

1.XXX (no decimal point):the smallest unit is 1Hz,the range 1Hz-999Hz

2.XX.X (decimal point in ten): The minimum unit is 0.1Khz; the range of 0.1KHz-99.9KHz

3.X.X.X.(there is three decimal point): the smallest unit is 1Khz; the range 1KHz-150KHz

Frequency Display Example:

1.”100″ indicates that the PWM output pulse of 100Hz

2.”54.1″ indicates that the PWM output pulse of 54.1KHz

3.”1.2.4.” Indicates that the PWM pulse output 124KHz

4.Duty Cycle in the range:0 to 100

5. Three frequencies duty cycle is the same, all the parameters non-volatile

Features:

1. 2.54mm pin interface leads
2. Long service life and stable performance
3. Standard interface and electronic building blocks
4. Widely use in Arduino DIY projects
5. Cross rocker as a two-way 10K resistor, with the rocker in a different direction.

Package Includes:

1 x JoyStick Module PS2 Breakout Sensor + Knob Hat

Heart Rate data can be used in many Electronic design and microcontroller projects. But the heart rate data is difficult to read, however, the Pulse Sensor Amped help us to read heart rate. The Heart Beat Pulse Sensor Amped is a plug-and-play heart-rate sensor for Arduino.

It can be used by students, artists, athletes, makers, and game & mobile developers who want to easily incorporate live heart-rate data into their projects.

Pulse Sensor Amped adds amplification and noise cancellation circuitry to the hardware. It’s noticeably faster and easier to get reliable pulse readings. Pulse Sensor Amped works with either a 3V or 5V Arduino.

Pulse Sensor Arduino Hookup

Connect the sensor’s power supply pins to the Arduino board supply pin as Red – 5V, Black – GND and Purple – A0 (analog input 0) its over. This Analog input reading can be displayed in the serial terminal of Arduino IDE or it can be drawn as the pulse by using Processing IDE.

Features :

1. A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required.
2. The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything.
3. Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting.

Package Includes :

1 x Heart Beat Pulse Sensor