Heart Rate Monitor Kit with AD8232 ECG sensor module

SKU: aa0186
280,00 EGP
Out of stock
SKU: aa0186 Categories: ,
Out of stock

Description

The Heart Rate Monitor Kit with AD8232 ECG sensor module Kit For Arduino is a cost-effective board use to measure the electrical activity of the heart. This electrical activity can be chart as an ECG or Electrocardiogram and output as an analog reading.

ECGs can be extremely noisy, the AD8232 Single Lead Heart Rate Monitor acts as an op-amp to help obtain a clear signal from the PR and QT Intervals easily. The ECG module AD8232 heart ECG monitoring sensor module is an integrated signal conditioning block for ECG and other bio-potential measurement applications.

The ECG Module AD8232 Heart ECG Monitoring Sensor Module Kit for Arduino is designed to extract, amplify, and filter small bio-potential signals in the presence of noisy conditions; such as those created by motion or remote electrode placement.

The AD8232 Heart Rate Monitor breaks out nine connections from the IC that you can solder pins, wires, or other connectors too. SDN, LO+, LO-, OUTPUT, 3.3V, GND provide essential pins for operating this monitor with an Arduino or other development board.

Also provided on this board are RA (Right Arm), LA (Left Arm), and RL (Right Leg) pins to attach and use your own custom sensors. Additionally, there is an LED indicator light that will pulsate to the rhythm of a heartbeat. Biomedical Sensor Pads and Sensor Cable are required to use the heart monitor and can be found in the Recommended Products section.

Pin Connections :

201509160917107120


  Steps:

  1. Go to the “Attachments” section of our product’s webpage. Download the ZIP file and Unzip it.
  2. Copy the folder into Arduino Folder or in the “Libraries” folder of  Arduino.
  3. Open the  Software folder. Now, Open “Heart_Rate_Display_Arduino” folder. In that folder, open the arduino file in arduino IDE.
  4. Compile and  upload the program. After uploading, check output in Serial Plotter.

Application
  1. Fitness and exercise heart rate monitoring
  2. Portable ECG
  3. Remote health care
  4. Gaming peripherals
  5. Biological signal acquisition
Note: This product is NOT a medical device and is not intended to be used as such or as an accessory to such nor diagnose or treat any conditions. 

Features :

  1. Designed to extract, amplify, and filter small biopotential signals in the presence of noisy conditions, such as those created by motion or remote electrode placement.
  2. Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart.
  3. AD8232 is an integrated signal conditioning block for ECG and other biopotential measurement applications.
  4. ECGs can be extremely noisy, the AD8232 Single Lead Heart Rate Monitor acts as an op-amp to help obtain a clear signal from the PR and QT Intervals easily.
  5. This electrical activity can be charged as an ECG or Electrocardiogram and output as an analog reading.
  6. Leads-Off Detection.
  7. Shutdown Pin.
  8. LED Indicator.
  9. Analog Output.
  10. 3.5 mm Jack for Biomedical Pad Connection.

Package Includes :

1 x Ecg module AD8232 heart ECG monitoring sensor module.
1 x Sensor cable.
3 x Electrode Pads.

Additional information

Weight 0,0000 g

Reviews

There are no reviews yet.

Be the first to review “Heart Rate Monitor Kit with AD8232 ECG sensor module”

Your email address will not be published. Required fields are marked *

Quick Comparison

SettingsHeart Rate Monitor Kit with AD8232 ECG sensor module removeMQ-2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module removeLM35DZ Temperature Sensor removeStrong Neodymium Magnets Bar, 30x10x5mm removeDS18B20 Water Proof Temperature Probe – Black (1m) removeDS18B20 Temperature Sensor remove
NameHeart Rate Monitor Kit with AD8232 ECG sensor module removeMQ-2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module removeLM35DZ Temperature Sensor removeStrong Neodymium Magnets Bar, 30x10x5mm removeDS18B20 Water Proof Temperature Probe – Black (1m) removeDS18B20 Temperature Sensor remove
Image
SKUaa0186MQ-2lm35dzaa0198DS18B20-WDS18B20
Rating
Price280,00 EGP70,00 EGP30,00 EGP10,00 EGP60,00 EGP28,00 EGP
Stock
Out of stock
Out of stock
Out of stock
Out of stock
Out of stock
Out of stock
AvailabilityOut of stockOut of stockOut of stockOut of stockOut of stockOut of stock
Add to cart

Read more

Read more

Read more

Read more

Read more

Read more

Description
Content

The Heart Rate Monitor Kit with AD8232 ECG sensor module Kit For Arduino is a cost-effective board use to measure the electrical activity of the heart. This electrical activity can be chart as an ECG or Electrocardiogram and output as an analog reading.

ECGs can be extremely noisy, the AD8232 Single Lead Heart Rate Monitor acts as an op-amp to help obtain a clear signal from the PR and QT Intervals easily. The ECG module AD8232 heart ECG monitoring sensor module is an integrated signal conditioning block for ECG and other bio-potential measurement applications.

The ECG Module AD8232 Heart ECG Monitoring Sensor Module Kit for Arduino is designed to extract, amplify, and filter small bio-potential signals in the presence of noisy conditions; such as those created by motion or remote electrode placement.

The AD8232 Heart Rate Monitor breaks out nine connections from the IC that you can solder pins, wires, or other connectors too. SDN, LO+, LO-, OUTPUT, 3.3V, GND provide essential pins for operating this monitor with an Arduino or other development board.

Also provided on this board are RA (Right Arm), LA (Left Arm), and RL (Right Leg) pins to attach and use your own custom sensors. Additionally, there is an LED indicator light that will pulsate to the rhythm of a heartbeat. Biomedical Sensor Pads and Sensor Cable are required to use the heart monitor and can be found in the Recommended Products section.

Pin Connections :

201509160917107120


  Steps:

  1. Go to the “Attachments” section of our product’s webpage. Download the ZIP file and Unzip it.
  2. Copy the folder into Arduino Folder or in the “Libraries” folder of  Arduino.
  3. Open the  Software folder. Now, Open “Heart_Rate_Display_Arduino” folder. In that folder, open the arduino file in arduino IDE.
  4. Compile and  upload the program. After uploading, check output in Serial Plotter.

Application
  1. Fitness and exercise heart rate monitoring
  2. Portable ECG
  3. Remote health care
  4. Gaming peripherals
  5. Biological signal acquisition
Note: This product is NOT a medical device and is not intended to be used as such or as an accessory to such nor diagnose or treat any conditions. 

Features :

  1. Designed to extract, amplify, and filter small biopotential signals in the presence of noisy conditions, such as those created by motion or remote electrode placement.
  2. Single Lead Heart Rate Monitor is a cost-effective board used to measure the electrical activity of the heart.
  3. AD8232 is an integrated signal conditioning block for ECG and other biopotential measurement applications.
  4. ECGs can be extremely noisy, the AD8232 Single Lead Heart Rate Monitor acts as an op-amp to help obtain a clear signal from the PR and QT Intervals easily.
  5. This electrical activity can be charged as an ECG or Electrocardiogram and output as an analog reading.
  6. Leads-Off Detection.
  7. Shutdown Pin.
  8. LED Indicator.
  9. Analog Output.
  10. 3.5 mm Jack for Biomedical Pad Connection.

Package Includes :

1 x Ecg module AD8232 heart ECG monitoring sensor module.
1 x Sensor cable.
3 x Electrode Pads.

If you are searching for a Gas sensor module with a very High detection range compared to any ordinary gas sensor then this MQ-2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module will fulfill your specification demands. The MQ-2 Gas sensor detector module has a detection range of 300-10000 ppm. The gas sensor modules are always well known for their robust and simple construction and measures toxic gases in very low concentrations.

The MQ-2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module is useful for gas leakage detection (home and industry). It is suitable for detecting H2, LPG, CH4, CO, Alcohol, Smoke, or Propane. Due to its high sensitivity and fast response time, measurements can be taken as soon as possible. The sensitivity of the sensor can be adjusted by the potentiometer.

MQ-2 gas sensor using gas sensitive material is to be clean air in the lower conductivity of stannic Oxide or tin oxide (SnO2). When the sensor when flammable gases are present in the environment in which the conductivity of the sensor with an increasing concentration of combustible gas in the air increases.

Use a simple circuit to convert the changes in conductivity and output signal that corresponds to the concentration of the gas.

MQ-2 gas sensor higher sensitivity to liquefied petroleum gas, propane, hydrogen, detection of gas, and other combustible vapors are ideal. This sensor can detect a variety of flammable gas, is a low-cost sensor for many applications.

MQ-2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module - ROBU.IN

Following conditions must be avoided

Water Condensation
Indoor conditions, slight water condensation will affect sensors’ performance lightly. However, if water condensation on sensors surface and keep a certain period, sensor’ sensitivity will be decreased.

Used in high gas concentration
No matter the sensor is electrified or not if a long time is placed in high gas concentration it will affect the sensor’s characteristics.

Longtime storage
The sensor’s resistance produces reversible drift if it’s stored for a long time without electrifying, this drift is related to storage conditions. Sensors should be stored in airproof without silicone gel bag with clean air. For the sensors with long time storage but no electrify, they need a long aging time for stability before using.

Longtime exposed to an adverse environment
No matter the sensors are electrified or not, if exposed to an adverse environment for a long time, such as high humidity, high temperature, or high pollution, etc, it will affect the performance of the sensor badly.

Vibration
Continual vibration will result in sensors’ down-lead response then rapture. In transportation or assembling lines, a pneumatic screwdriver/ultrasonic welding machine can lead to this vibration.

Concussion
If sensors meet strong concussion, it may lead its lead wire disconnected.

Explore more Gas Sensors click the link Gas Sensor

Application:
  1. The domestic gas leakage detector
  2. Industrial Combustible gas detector
  3. Portable gas detector

Features :

  1. Good sensitivity to Combustible gas in a wide range
  2. High sensitivity to LPG, Propane, and Hydrogen
  3. Long life and low cost
  4. Simple drive circuit
  5. Can be used as a digital or analog sensor
  6. The Sensitivity of the Digital pin can be varied using the potentiometer
  7. Can be used to Measure or detect LPG, Alcohol, Propane, Hydrogen, CO, and even methane

Package Includes :

1 x MQ-2 Smoke LPG Butane Hydrogen Gas Sensor Detector Module

You can use the lm35dz sensor in temperature measurement applications. Thanks to its small size, you can make more precise measurements by placing it in the area you want to measure the temperature.

Features:

  1. Calibrated directly in Degree Celsius (Centigrade)
  2. Linear at 10.0 mV/°C scale factor
  3. 0.5°C accuracy guarantee-able (at a25°C)
  4. Suitable for remote applications
  5. Low cost due to wafer-level trimming
  6. Operates from 4 to 30 volts
  7. Less than 60 mA current drain
  8. Low self-heating, 0.08°C in still air
  9. Non-linearity only 0.25°C typical
  10. Low impedance output, 0.1Ωfor 1 mA load

Scope of application:

  • power supplies
  • battery management systems
  • motor driver protection circuit

Package Included:

  • 1 x LM35DZ Temperature Sensor

 

Tiny neodymium magnets can be used for attachments in corrective devices or for holding together replacement dentures where several teeth are missing. Because of their strength, even tiny  can be effective and when coated they have an increased resistance to corrosion.


Features:

  1. Model: K8100
  2. Shape: Rectangular Magnetic Bar
  3. Size: 30x10x5mm
  4. Color: Silver
  5. Lightweight
  6. Supper neodymium magnets
  7. Easy to handle

Packages Includes: 

1 x Strong Neodymium Magnets Bar, 30x10x5mm

DS18B20 Temperature Sensor Module is a digital temperature sensor, and you can easily connect it to Arduino with only one 4.7-pound resistor, base 1 – Ground 2 – Output – Base 3 to the positive of the source, with resistance to base 2 Is connected. The connection of this sensor to the Arduino via the 1-wire protocol is established. Therefore, several sensors can be connected only through one common wire to Arduino. The output is digitally accurate to 12 bits. Therefore, the temperature can be measured with a precision of 0.0625 º C.

Applications:
DS18B20 Temperature Sensor is suitable for the cold storage, granaries, storage tanks, telecommunications room, electric power room, cable trough, and other temperature measurement and control areas; bearing, cylinder, textile machinery, air conditioning, and other small space industrial equipment temperature and control; , Refrigerator, freezer, and low-temperature drying oven, etc. heating/cooling pipe calorie measurement, central air conditioning household thermal energy measurement and industrial temperature measurement and control and Many more..

Features:

  1. Digital signal output
  2. 18B20 Temperature Sensor Chip
  3. Resolution adjustment ranges from 9-12 bytes.
  4. Send data via a pin
  5. Temperature measurement ranges: -55°C to +125°C, be accurate to 0.5°C.

Package Includes:

1 x DS18B20 Temperature Sensor Module

Weight0.00000.00000.00000.00000.00000.0000
DimensionsN/AN/AN/AN/AN/AN/A
Additional information
Weight 0,0000 g
Weight 0,0000 g
Weight 0,0000 g
Weight 0,0000 g
Weight 0,0000 g
Weight 0,0000 g
Select the fields to be shown. Others will be hidden. Drag and drop to rearrange the order.
  • Image
  • SKU
  • Rating
  • Price
  • Stock
  • Availability
  • Add to cart
  • Description
  • Content
  • Weight
  • Dimensions
  • Additional information
  • Attributes
  • Custom attributes
  • Custom fields
Click outside to hide the comparison bar
Compare