Servo Motor MG996R Metal Gear (With Accessories)

TowerPro Servo Motors are optimum-quality and affordable cost servos.! They are suitable for a wide range of applications, including RC aircraft, automobiles, and robotics, Or just to have some fun with whatever crazy project you’re working on.

When you purchase TowerPro motors in India, they are almost usually NOT ORIGINAL, and these are no exception… These are NOT ORIGINAL Tower Pro Servos, either. However, they are dead cheap and Serve the purpose. We put them to the test and found them to be of good quality for the price.

Wire Description

• Red – Positive
• Brown – Negative
• Orange – Signal

Features:

1. Gear Type: Metal gear
2. Servo Plug: JR (Fits JR and Futaba)
3. Servo arms & screws included, and fit with Futaba servo arm
4. It’s a universal “S” type connector that fits most receivers, including Futaba, JR, Hitec , GWS, Cirrus, Blue Bird, Blue Arrow, Corona, Berg, and Spektrum.
5. CE & RoHS approved
6. We have upgraded our servo gear set and shaft to aluminum 6061-T6. It is stronger and lighter than copper.

Package Includes:

1 x TowerPro MG996R Digital High Torque Servo Motor and Accessories Parts(as shown in the image)

This is ULN2003 Driver Module Stepper Motor Driver Board for driving and controlling stepper motors.

ULN2003 Stepper Motor Driver Board uses the ULN2003 DARLINGTON ARRAYS to drive the 4-phase 5-wire stepper motor (5v-12v).

It’s easy to use Arduino or another development platform to drive the stepper motor by this diver board.

The 5 Line 4 Phase can be driven by ordinary ULN2003 chip can also be connected in phase 2 development board used for supporting the use of a direct plug and easy to use stepper motor used in the development board. A, B, C, D four-phase LED indicates the status of the stepper motor work.

Features :

1. ULN2003A motor driver chip
2. Chip all the pins already leads for easy connection to use
3. 5-12V power supply
4. 4-way signal indicator
5. XH-5P socket can be connected directly 28BYJ-48 Model stepper motor

Package Includes :

1 x ULN2003 Driver Module Stepper Motor Driver Board

Description: A2212/10T 1400KV Brushless Outrunner Motor

1400KV A2212 2212 10T 1400KV Brushless Motor BLDC Motor 2-3S Outrunner Motor With 3.5mm Male Banana Bullet Plug Jack Fixed Wing For F450 S500 Frame RC Drone Airplane Aircraft Multi-Copter Quad-Copter Helicopter

These are the best low price drone motors available in the market. Then here is the best deal for you !!!! These are our market cracking Brushless Motors when it comes to bestselling drone motors. The uniqueness of this BLDC Motor lies in low cost and highly satisfying performance in fly. These brushless motors for drones are imported from China. Our quality control team then test some of the random motors from each batch before setting them on sell. The A2212 10T 13T 1400Kv Brushless Motors for Drone are best compatible or used with SimonK 30A ESC and 1045 Propeller Set. This 1400kv brushless motor is equipped with the solid metal case which makes it reliable and durable. This A2212 10T Motor comes with the pre-soldered good quality connector for a fast and direct connection between ESC and the motor.

Specifications:

• Model: A2212 / 10T
• RPM / V: 1400 kV
• Maximum efficiency: 80%
• Maximum current performance: 4-10 A
• Current: 12 A / 60 s
• Working voltage: 7-12V

Application:

• Multirotors
• RC Airplanes
• UAV

Features:

• The steel design is capable of withstanding competitional conditions.
• Lightweight design makes them suitable for a wide range of Quadcopter and Hexacopter Frames.
• Compact size.
• Offers great performance and value for money.
• Smooth throttle response for best RC experience.

You might be searching for a pump that operates on 12 V and gives an output of above 240L/H then this could be the best choice for your project.

This Ultra-Quiet DC 12V 3M 240L/H Brushless Submersible Water Pump is a low-cost, small size Submersible Pump. It can take up to 240 liters per hour with a very low current consumption from 300mA. Just connect the tube pipe to the motor outlet, submerge it in water, and power it. The black color pump comes with a heavy-duty cable and a 5mm DC female jack at the end to connect directly to the 12V power supply.  It is widely used in prototype projects as well as for decoration purposes.

We at robu.in have diversified ranges of  pumps, Click here

Caution:

Make sure that the water level is always higher than the motor. The dry run may damage the motor due to heating and it will also produce noise.

Features :

1. Super long working life(more than 30000 hours); Adopt high-performance ceramic shaft.
   
2. The axis is enclosed with static sealing, not dynamic, which can avoid leaking problems.
3. Amphibious design; Submersible installation and entirely waterproof.
4. low consumption; low noise(less than 35db),  used in computer cooling system, Garden fountain.
5. Used in Aquarium, car cooling, humidifier, air conditioner, other cooling and circulation systems.

Package Includes :

1 x Ultra-Quiet DC 12V 3M 240L/H Brushless Submersible Water Pump

If you want to make a robot which has lots of moving parts or if you want to control too many LEDs with PWM outputs,  then the limited PWM outputs of your microcontroller would be a big problem for you. To overcome this problem, the only thing you should do is to get a 16-Channel 12-Bit PWM/Servo Driver.

You can control 16 free-running PWM outputs with 16-Channel 12-Bit PWM/Servo Driver using only 2 pins. You can even chain up 62 breakouts to control up to 992 PWM outputs.

It’s an I2C-controlled PWM driver with a built-in clock. That means you do not need to continuously send it to signal to tie up your microcontroller, it is completely free running!

It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs. This is good when you want to control white or blue LEDs with 3.4+ forward voltages. 6 address select pins so you can wire up to 62 of these on a single I2C bus, a total of 992 outputs.

Features :

1. Adjustable frequency PWM up to about 1.6 KHz
2. 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
3. Configurable push-pull or an open-drain output
4. The output enable pin to quickly disable all the outputs
5. Terminal block for power input
6. Reverse polarity protection on the terminal block input
7. Green power-good LED
8. 3 pin connectors in groups of 4 so you can plug in 16 servos at once
9. Chainable design
10. A spot to place a big capacitor on the V+ line
11. 220-ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial.
12. This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers.

Package Includes :

The Double BTS7960 43A H-Bridge High-Power Stepper Motor Driver Module is; a fully integrated high current H bridge for motor drive applications using the BTS7960 high current half bridge. the BTS7960 is part of the NovalithICTM family. This containing one p-channel high side MOSFET and one n-channel low side MOSFET; with an integrated driver IC in one package. Due to the p-channel high side switch; the need for a charge pump is eliminated thus minimizing EMI.

Interfacing to a microcontroller is made easy by the integrated driver IC which features logic level inputs; diagnosis with current sense, slew rate adjustment; dead time generation and protection against overtemperature, overvoltage, under voltage; overcurrent, and short circuit.
The Double BTS7960 43A H-Bridge High-Power Stepper Motor Driver Module provides; a cost-optimized solution for protected high current PWM motor drives with very low board space consumption.

Features :

1. PWM capability of up to 25 kHz combined with active freewheeling.
2. Switched mode current limitation for reduced power dissipation in overcurrent.
3. Status flag diagnosis with current sense capability.
4. Overtemperature shut down with latch behavior.
5. Overvoltage lockout.
6. Undervoltage shut down.
7. Driver circuit with logic level inputs.
8. Adjustable slew rates for optimized EMI.
9. 74AHC244 Schmitt-trigger Octal buffer/line driver for ESD protection (Inputs accepts voltages higher than VCC).

Input port:

1. RPWM: forward level or PWM signal input, active high.
2. LPWM: Reverse level or PWM signal input, active high.
3. R_EN: forward drive enable input, high-level enable, low level off.
4. L_EN: Reverse drive enable input, high-level enable, low level off.
5. R_IS: forward drive current alarm output.
6. L_IS: Reverse drive current alarm output.
7. VCC: +5 V power output, 5V power supply connection with the microcontroller.
8. GND: signal common low end.

Package Includes :

1 x Double BTS7960 43A H-Bridge High-Power Stepper Motor Driver Module.