N20-6V-100 RPM Micro Metal Gear-box DC Motor

This N20-6V-100 Rpm Micro Metal Gear Motor has small volume, torsion big, all metal gear, durable, not easy to wear. Great replacement for the rusty or damaged DC geared speed reduce motor on the machine. Widely used on Boat, Car, Electric Bicycle, Fan, Home Appliance.

The N20 Micro Gear 6V 100 RPM DC Motor (High Torque) is lightweight, high torque, and low RPM motor. It is equipped with gearbox assembly so as to increase the torque of the motor. It has a cross-section of 10 × 12 mm, and the D-shaped gearbox output shaft is 9 mm long and 3 mm in diameter. It has a very small size so as fit in complex spaces of small-scale application. One can connect this Micro Gear Motor to wheels to drive them from one place to other while carrying high loads.

This N20 Micro Gear 100RPM 6V DC Motor (High Torque) has small volume, torsion big, all metal gear, durable, not easy to wear. Great replacement for the rusty or damaged DC geared speed reduce motor on the machine. Widely used on Boat, Car, Electric Bicycle, Fan, Home Appliance.

Motors with the variety of torque and speed ranging from low to high are available at BOT Electronics.

Features :

1. This is a DC Mini Metal Gear Motor, ideal for making robots
2. Lightweight, high torque and low RPM.
3. Fine craftsmanship, durable, not easy to wear.
4. With excellent stall characteristics, can climb hills easily.
5. You can also easily mount a wheel on the motor’s output shaft.

Package Includes :

1 x N20-6V-100 RPM Micro Metal Gear-box DC Motor

If you want to make a robot which has lots of moving parts or if you want to control too many LEDs with PWM outputs,  then the limited PWM outputs of your microcontroller would be a big problem for you. To overcome this problem, the only thing you should do is to get a 16-Channel 12-Bit PWM/Servo Driver.

You can control 16 free-running PWM outputs with 16-Channel 12-Bit PWM/Servo Driver using only 2 pins. You can even chain up 62 breakouts to control up to 992 PWM outputs.

It’s an I2C-controlled PWM driver with a built-in clock. That means you do not need to continuously send it to signal to tie up your microcontroller, it is completely free running!

It is 5V compliant, which means you can control it from a 3.3V microcontroller and still safely drive up to 6V outputs. This is good when you want to control white or blue LEDs with 3.4+ forward voltages. 6 address select pins so you can wire up to 62 of these on a single I2C bus, a total of 992 outputs.

Features :

1. Adjustable frequency PWM up to about 1.6 KHz
2. 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate
3. Configurable push-pull or an open-drain output
4. The output enable pin to quickly disable all the outputs
5. Terminal block for power input
6. Reverse polarity protection on the terminal block input
7. Green power-good LED
8. 3 pin connectors in groups of 4 so you can plug in 16 servos at once
9. Chainable design
10. A spot to place a big capacitor on the V+ line
11. 220-ohm series resistors on all the output lines to protect them, and to make driving LEDs trivial.
12. This board/chip uses I2C 7-bit address between 0x60-0x80, selectable with jumpers.

Package Includes :

Material: ABS

1. The yellow color
2. Product quote for 2 axes and 8folhas from 2conjuntos quote.
3. Wind leaf overall diameter: Φ100mm
4. Wind leaf total height: 60mm
5. Shaft hole diameter: 1.95mmΦ (mounting shaft 2.0mm)
6. Wind page number: 4pcs
7. For the mass production plant, there is a little burr forward, but not the effect on use.
8. Size: see the picture below
9. No retail package
10. Quantity: 1pc

Note: Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!!

Package includes:

• 1pc xMini Wind Turbine Blade Vertical Ax Micro Generator Blades Set Small New

This Flat 1034 Mobile Phone Vibrator Motor is a shaftless vibration motor that is fully-enclosed with no exposed moving parts. Its small size (10 mm diameter, 3.4 mm height) and shaftless design mean you can mount it on a PCB or even place it in a pocket to add quiet, haptic feedback to your project.

The motor has a 3M adhesive backing on it for easy mounting and 1.5″ leads for making quick connections. Polarity is not important; the motor can run CW or CCW.

This tiny, button-type, vibrating motor shakes with a vibration amplitude of 0.75g and draws approximately 60 mA when 3 V is applied to its leads.

Package Includes :

1 x Flat 1034 Mobile Phone Vibrator Motor.

This is DIY Mini Wind Turbine Blade Vertical Axis Micro Generator Blades Small Set.

Package includes :

• 1 x Motor With LED light.
• 4 x Vertical Blade.
• 1 x Blade Mounting Head.