Servo Motor TowerPro MG995

L298N 2A Based Motor Driver is a high power motor driver perfect for driving DC Motors and Stepper Motors .

It uses the popular L298 motor driver IC and has an onboard 5V regulator which it can supply to an external circuit. It can control up to 4 DC motors, or 2 DC motors with directional and speed control.

This motor driver is perfect for robotics and mechatronics projects and perfect for controlling motors from microcontrollers, switches, relays, etc. Perfect for driving DC and Stepper motors for micro mouse, line following robots, robot arms, etc.

Usage:
H-bridges are typically used in controlling motors speed and direction but can be used for other projects such as driving the brightness of certain lighting projects such as high powered LED arrays.

How it works:
An H-Bridge is a circuit that can drive a current in either polarity and be controlled by *Pulse Width Modulation (PWM).

* Pulse Width Modulation is a means in controlling the duration of an electronic pulse. In motors try to imagine the brush as a water wheel and electrons as the flowing droplets of water. The voltage would be the water flowing over the wheel at a constant rate, the more water flowing the higher the voltage. Motors are rated at certain voltages and can be damaged if the voltage is applied to heavily or if it is dropped quickly to slow the motor down. Thus PWM. Take the water wheel analogy and think of the water hitting it in pulses but at a constant flow. The longer the pulses the faster the wheel will turn, the shorter the pulses, the slower the water wheel will turn. Motors will last much longer and be more reliable if controlled through PWM.

Pins Details
Out 1: Motor A lead out
Out 2: Motor A lead out
Out 3: Motor B lead out
Out 4: Mo (Can actually be from 5v-35v, just marked as 12v)
GND: Ground
5v: 5v input (unnecessary if your power source is 7v-35v, if the power source is 7v-35v then it can act as a 5v out)
EnA: Enables PWM signal for Motor A (Please see the “Arduino Sketch Considerations” section)
In1: Enable Motor A
In2: Enable Motor A
In3: Enable Motor B
In4: Enable Motor B
EnB: Enables PWM signal for Motor B (Please see the “Arduino Sketch Considerations” section)

Two things to mention;

Make sure you have all of your grounds tied together; Arduino, Power source, and the Motor Controller.
The PWM Pins are unnecessary if you do not want to control PWM features.
ARDUINO SKETCH CONSIDERATIONS :
The Arduino code sketch is pretty straightforward. Since there isn’t a library for the L298N Dual H-Bridge Motor Controller you just have to declare which pins the controller is hooked to.

The “int dir(number)Pin(letter)”‘ pins can be connected to any available digital pin you have available, as long as you declare the correct pin in your sketch. This makes the L298N Dual H-Bridge Motor Controller very versatile if your project is using a lot of Arduino pins.

The int“speedPin(letter)” pins need to be connected to a PWM pin on the Arduino if you want to enable speed control through PWM.

As a quick cheat I have included a list of PWM pins for the main two types of Arduino’s I use:

AT MEGA – PWM: 2 to 13 and 44 to 46. Provide 8-bit PWM output with the analogWrite() function.
UNO – PWM: 3, 5, 6, 9, 10, and 11. Provide 8-bit PWM output with the analogWrite() function.

Features:

1. Maximum motor supply current: 2A per motor.
2. Current Sense for each motor.
3. Heatsink for better performance.
4. Power-On LED indicator.
5. Double H bridge Drive Chip: L298N.

Package Includes :

1. 1 x L298N 2A Based Motor Driver Module – Good Quality

Material: ABS

1. The yellow color
2. Product quote for 2 axes and 8folhas from 2conjuntos quote.
3. Wind leaf overall diameter: Φ100mm
4. Wind leaf total height: 60mm
5. Shaft hole diameter: 1.95mmΦ (mounting shaft 2.0mm)
6. Wind page number: 4pcs
7. For the mass production plant, there is a little burr forward, but not the effect on use.
8. Size: see the picture below
9. No retail package
10. Quantity: 1pc

Note: Due to the difference between different monitors, the picture may not reflect the actual color of the item. Thank you!!

Package includes:

• 1pc xMini Wind Turbine Blade Vertical Ax Micro Generator Blades Set Small New

12V DC Solenoid Water Air Valve Switch (Normally Closed) – 1/2″ controls the flow of fluid (liquid or air) and acts as a valve between high-pressure fluid! This liquid valve would make a great addition to your robotic gardening project. There are two ½” (Nominal NPT) outlets. Normally, the valve is closed. When a 12V DC supply is applied to the two terminals, the valve opens and water can push through.

The valve works with the solenoid coil which operates electronically with DC 12 volt supply. As it is a normally closed assembly, it opens the flow of fluids as soon as it is powered ON and stops/blocks the flow when the supply voltage removed.

Note:  While Connecting Valve in Flow pipeline, you need to mind the Input and Output direction of the valve. It will work only if you connect it in the right direction. (Hint: Inside the value, at one side you will find the filter this is the input side of the value)

Features:

1. Compact and convenient.
2. Easily installed and serviced
3. Precise and reliable.
4. The installation direction can be arbitrary Angle
5. Pressure-regulating valve (steady flow valve) function similar to the water flow switch
6. Not only can it provide a steady flow, but it also prevents the dry burning.
7. Suitable for fluids like water, oil, air.

Package Includes:

1 x 12V Solenoid Water Air Valve Switch (Normally Closed) – 1/2″

The Towerpro MG90S Mini Digital Servo is 180° rotation servo. It is a Digital Servo Motor which receives and processes PWM signal faster and better. It equips sophisticated internal circuitry that provides good torque, holding power, and faster updates in response to external forces.

The good optimized performance and reliability of our servos have made them the favorite choice of many RC hobbyists.

They are packed within a tight sturdy plastic case which makes them water and dust resistant which is a very useful feature in RC planes, Boats, and RC Monster Trucks etc. It equips 3-wire JR servo plug which is compatible with Futaba connectors too.

Wire Description

RED – Positive

Brown – Negative

Orange – Signal

Features : 

1. High resolution
2. Accurate positioning
3. Fast control response
4. Constant torque throughout the servo travel range
5. Excellent holding power

Package Includes : 

1 x Towerpro MG90S Mini Digital 180 Degree Servo

Set of Horns

1. One Point
2. Two Point
3. Four Point

1 x Set of Screws