Speed Measuring Sensor Groove Coupler Module For Arduino

This is Speed Measuring Sensor Groove Coupler Module For Arduino. The DO output interface can be directly connected to a micro-controller IO port if there is a block detection sensor, such as the speed of the motor encoder can detect.

DO modules can be connected to the relay, limit switch, and other functions, it can also with the active buzzer module, compose alarm. Widely used in motor speed detection, pulse count, the position limit, etc.

Wiring Specification :

1. VCC: The positive 3.3-5 v power supply.
2. GND: Connect power negative.
3. DO: TTL switch signal output.
4. AO: This is analog output.

Feature :

1. Using imported groove optical coupling sensor, width 5mm.
2. It has the output state light, if output high level, the lights are off. if output low level, it on.
3. If it covered, it will output high level; otherwise, its output low level.
4. Good signal and waveform, with a strong driving ability for more than 15mA.
5. Equipped with a fixed bolt hole, easy install.
6. Use the LM393 wide voltage comparer.
7. The DO output interface can be directly connected to a micro-controller IO port if there is a block detection sensor, such as the speed of the motor encoder can detect.
8. DO modules can be connected to the relay, limit switch, and other functions, it can also with the active buzzer module, compose alarm.

Package Includes :

1 x Speed Measuring Sensor Groove Coupler Module For Arduino.

The DHT11 Temperature And Humidity Sensor Module with LED is a small humidity and temperature sensor that you can connect to your Arduino and get readings for temperature and humidity in the environment.

Features:

• DHT11 sensor with PCB and LED indicator along with cable; 3 to 5V power and I/O, 4 pins with 0.1″ spacing
• The board has pre-built 4.7K or 10K resistor, which you will need to use as a pull-up from the data pin to VCC.
• 2.5mA max current use during conversion (while requesting data)
• Good for 20-80% humidity readings with 5% accuracy
• Good for 0-50°C temperature readings ±2°C accuracy.

Package Includes:

• 1 x DHT11 Temperature And Humidity Sensor Module.
• 3 x Female to Female Connecting cable.

This ultrasonic sensor is very similar to the ultrasonic sensors  which are found in cars. This Waterproof Ultrasonic Obstacle Sensor shows some important constructional advantages over the conventional sensors. It comes in two separate parts one being the transducer which is the sensing element and the other being the control board.

The module is capable of providing information of the objects between the distance range of 250 mm to 4500 mm. The great advantage of using this Waterproof Ultrasonic Obstacle Sensor is you can put the sensing element far away from all the control circuitry.

This Ultrasonic Distance Sensor is an industrial-grade sensor to measure distance. Interfacing with it is the same as another cheap ultrasonic sensor, but it offers better performance and is compatible with harsher environments and is waterproof too! Arduino  It can be easily interfaced with and Sample codes and projects are available.

There are many ultrasonic distance sensors on the market, but sometimes, this kind of sensor needs to work in vulnerable conditions. This Waterproof Ultrasonic Obstacle Sensor meets this requirement. It has a good performance and almost the same usage of an HC-SR04 module.

It is very easy to use, a control port with a 10US above high level can wait for high-level output at the receiving port. An output can drive the timer when this port is low can read the timer value, this time for the location of the time can be distance measurement. Constantly cycle tests that can achieve the measurement of the value of your mobile.

The basic working principle:

1. Turn on TRIG Pin to 5V for at least 10uS
2. The module will then automatically send 8 40KHz tones and automatically detect when the signal return after reflecting back from the object
3. Upon detecting the signal, a high-level signal is outputted through the IO Pin ECHO. By keeping track of the time duration between transmitting and receiving the signal, the distance can be calculated. Distance = (Time to Receive Reflected Signal * speed of sound (340M/S)) /2

Wiring

+5V(positive)

Trig(control)

Echo(receive)

GND(negative)

Application :

1. Horizontal distance
2. Obstacle avoidance, automatic control
3. Traffic control
4. Security, industrial control
5. Artificial intelligence, and research.

Features:

1. Small size, easy to use.
2. Low voltage, low power consumption.
3. High accuracy.
4. Strong anti-jamming.
5. Integrated with wire enclosed waterproof probe, suitable for wet, harsh measurement occasions.

Package Includes :

1 x Waterproof Ultrasonic Obstacle Sensor, with 2.5m Separate Probe.

The resistance of 10mm GL12528 Light Sensitive Photoresistor LDR changes with the change in the ambient light exposed on the surface of the sensor. As the light on the sensor increases then the resistance across the two leads decreases. Light Dependent Resistor is a type of photocell which finds excellent use in light sensing device application, whether it is automatic outdoor light ON/OFF switch or indoor automatic light switch; moreover, the 10mm LDR or photoresistor sensor works best in both light and dark regions. The photo-resistors are a staple of electronics. If you need a way to sense the level of ambient light then there is no easier way to do it without an LDR/photo-resistor.

Two Cadmium Sulphide PhotoConductive Cells with spectral responses similar to that of the human eye. Cell resistance falls with increasing light intensity. Applications of this product include smoke detection, automatic lighting control, batch counting, and burglar alarm systems. Furthermore, some of the applications are given below.

 Analog Applications:

To know more about photo-resistor, click here. What is photo-resistor?

Features:

1. Spectral peak: 560nm
2. Maximum voltage: 250 VDC
3. Maximum wattage: 200 mW
4. Operating temperature: -30˚C ~ +70˚C
5. Light resistance (10 Lux): 10-20 KΩ
6. Dark resistance: 2 MΩ
7. Resistance illumination: 3
8. Response time: 20ms (Rise), 30ms (Down)

Package Includes :

This is JoyStick Module PS2 Breakout Sensor very similar to the ‘analog’ joysticks on PS2 (PlayStation 2) controllers. Directional movements are simply two potentiometers – one for each axis. Pots are ~10k each. This joystick also has a select button that is actuated when the joystick is press down.

With the help of this Joystick Module, you can measure position coordinates on the X and Y axis by moving the “hat”. It also contains a switch that is press-able by pushing the “hat”.It also contains a switch that is press-able by pushing the “hat” down. Similar to the XBOX controller.

The X and Y axes are two 10k potentiometers which control 2D movement by generating analog signals. When the module is in working mode, it will output two analog values, representing two directions. This module uses the 5V power supply, and value, when reading through analog input, would be about 2.5V, a value will increase with joystick movement and will go up till maximum 5V; the value will decrease when the joystick is moved in other direction till 0V.

Applications:

1.As square wave signal generator which generates a square wave signal

2. To provide a signal to the stepping motor driver

3. Adjustable pulse generation for chip use

4. Produce variable pulse signal, the control-related circuit (PWM dimming, speed)

Module Description:

Frequency is divided into three ranges:

1.XXX (no decimal point):the smallest unit is 1Hz,the range 1Hz-999Hz

2.XX.X (decimal point in ten): The minimum unit is 0.1Khz; the range of 0.1KHz-99.9KHz

3.X.X.X.(there is three decimal point): the smallest unit is 1Khz; the range 1KHz-150KHz

Frequency Display Example:

1.”100″ indicates that the PWM output pulse of 100Hz

2.”54.1″ indicates that the PWM output pulse of 54.1KHz

3.”1.2.4.” Indicates that the PWM pulse output 124KHz

4.Duty Cycle in the range:0 to 100

5. Three frequencies duty cycle is the same, all the parameters non-volatile

Features:

1. 2.54mm pin interface leads
2. Long service life and stable performance
3. Standard interface and electronic building blocks
4. Widely use in Arduino DIY projects
5. Cross rocker as a two-way 10K resistor, with the rocker in a different direction.

Package Includes:

1 x JoyStick Module PS2 Breakout Sensor + Knob Hat